PF-2 Big Berkey Fluoride Filters 2-Pack
PF-2 Big Berkey Fluoride Filters 2-Pack
PF-2 Big Berkey Fluoride Filters 2-Pack
PF-2 Big Berkey Fluoride Filters 2-Pack
PF-2 Big Berkey Fluoride Filters 2-Pack
PF-2 Big Berkey Fluoride Filters 2-Pack
Shower Filter Store

PF-2 Big Berkey Fluoride Filters 2-Pack

SKU: PF-2
$103.99 USD

Berkey Fluoride Reduction Filters

Product Code: PF-2

This popular item is currently on a PRE-ORDER status. The manufacturer has had limited production.

Order Now! Most orders are shipping with in 2 weeks.

In stock
On backorder

Need personalized supplement recommendations?

Get in touch

The PF-2™ Fluoride Reduction filters are designed for use in conjunction with Black Berkey water purification filters to adsorb the following unwanted elements found in drinking water.
  • Fluoride
  • Arsenic V and pre-oxidized Arsenic III
  • Other residual heavy metal ions
The Fluoride filters easily install without tools as they attach to the threaded ends at the bottom of  the Black Berkey filters
.
The media used in the PF-2 fluoride filter elements contains high-grade inert, activated alumina (Al2O3), which currently is the most efficient media available for extracting fluoride from water.
Under normal conditions it is recommended that each set of two PF-2™ filters be replaced after 1,000 gallons (3,785 liters).  If the Berkey system is refilled about one time per day, the PF-2’s should be replaced after 10 months, if the system is refilled about twice per day, the PF-2’s should be replaced about every five months). Actual capacity is dependent on the presence of other competing contaminants in the source water. High levels of fluoride, arsenic and heavy metals may reduce the capacity and efficiency of the elements.

Priming The Berkey Fluoride Filters

Priming the Berkey Fluoride water filter before use is necessary in order for the elements to perform properly. The filter medium inside the fluoride reducing element contains some residual manufacturing dust that may make the final water product cloudy or have a bitter taste. This situation is easily avoided by simply flushing the fluoride filter prior to the first use. Follow the instructions below to assure that your Berkey water filter system performs to its fullest potential.

PF-2 Fluoride filter priming instructions

Caution: Filters must be primed prior to use. Do not install before reading installation procedures – do not screw the PF-2 elements on more than eight revolutions or the core of the filter could be damaged.
  • With the blue caps in place wash the exterior of each PF-2 fluoride element with water and a mild dish washing soap.
  • With clean hands, remove both blue caps from each end of both filter elements.
  • Place the rubber priming button (tan colored) onto one end of a PF-2 and align the hole of the filter with the hole of the rubber washer.
  • Press the priming button up against the sink faucet so that the priming button creates a seal between the faucet and the PF-2 element.
  • While holding the priming button against the faucet, turn on the cold water slowly, allowing water to fill the cavity of the filter and discharge from the opposite end. Allow water to flow for at least 30 seconds or until water runs clear whichever is longer
  • Hint: place thumb on top of the faucet to apply pressure, this creates a better seal.
  • Turn the Pf-2 filter over and prime the opposite end (reversing the flow of water) repeating steps 3 thru 5 until water runs clear from both directions.
  • When you think the filters are flushed long enough, run some of the water that is being flushed through the filter into a clear glass and hold it up to the light to see if all of the cloudiness is gone from the water, if not continue priming until water is clear.
  •  This filter is now primed and ready to install.
Prime each of the PF-2 elements as described above.

“We have city water with added fluoride…not good! These filters are one of the few on the market that remove it.” ~ MICHELE G. from Stow, Ohio

We have city water with added fluoride…not good! These filters are one of the few on the market that remove it.
Did you find this helpful? 0 of 2 Found Helpful
Reviewed by: (Verified Buyer) MICHELE GIARRANO from Stow, Ohio
  • Fluoride Removal: Tested to greater than 95% fluoride reduction
  • Other Contaminants: Targets arsenic oxide anions and arsenic cations.
  • Capacity: 1000 gallon capacity or 307 refills
  • Installation: Easy to install – no tools necessary Dimensions:6? x 2.5?
  • Product Code: PF-2

All products have a 30-day money-back guarantee from date of purchase. Money-back guarantee does not apply if filter has been damaged due to misuse, improper installation, excessive water pressure or temperature, freezing or general misapplication of the filters use and purpose. For a product refund, return filter to place of purchase (15% restocking fee may apply). A sales receipt or proof of purchase must be included. All returns require a Return Authorization number. Shipping on all returned merchandise is the sole responsibility of the buyer unless otherwise specified.

Free Shipping is a standard 7-10 business days. Expedited Shipping is 3-4 business days however this does not apply to international orders. ALL international orders attract a shipping fee including orders to Canada, Puerto Rico, Hawaii, and all other US territories.

Ground Shipping Schedule (Free Shipping in the continental U.S., lower 48 states ONLY)

In-stock orders placed before noon central time are usually shipped the same business day.

In-stock orders placed after noon central time will usually ship the following business day.

International Shipments:

International orders must be purchased with PayPal. All International orders, unless otherwise requested, will ship via U.S.P.S. Global Priority Mail (6-14 business days’ delivery) in order to conserve costs and additional duties and fees
Subscribe and Save

Auto-renews, skip or cancel anytime.

To add to cart, go to the product page and select a purchase option